Introduction of Panasonic A6 Series Motor & Driver -- 2.1 Conformance to International Standards

Abstract

The Panasonic A6 series of AC servo motor and driver conformance to internation standards such as CE, CRRUS, KC, TUV UL etc. for the safety of your machinery around the world.

The AC servos meet the relevant EC Directives for Low Voltage Equipment so that the machine or equipment comprision our AC servos can meet EC Directive.

MINAS Servo System conforms to relevant standard under EMC Directives setting up certain model (condition) with certain locating distance and wiring or the servo motor and the driver. And actual working condition often differs from this model condition especially in wiring and grounding. Therefore, in order for the machine to conform to the EMC directives, especially for noise emission and noise terminal voltage, it is neceessary to examine the machine incorporating our servos.

1. Installation environment
   Use the driver in an environment of Pollution Degree 2 or 1 prescribed in IEC60664-1
   Use a copper cable with temperature rating of 75°C or higher.
   Make sure to install a circuit breaker (MCCB) or fuse which are UL recognized on the power supply.
   Remarks → Use a copper cable with temperature rating of 75°C or higher.
2. Short-Circuit Current Rating (SCCR).
   This driver conform to the power source witch is less than the maximum input voltage less than 5000A symmetrical current.
3. The NEC (National Electric Code).
   The branch circuit of the protection NEC (National Electrical Code) and regional standards according to the embodiment.
4. Over-load protection and over-temperature protection
   Drivers
   Over-load protective function will be activated when the effective current exceeds 115% or more than the rated current based on the time characteristics.
   Motor over-load-temperature protection shall be provided at the final installation upon required by the NEC (National Electric Code).

---

Note → For rated current of circuit breaker and fuse, refer to P.2-10 "Driver and List of Applicable Peripheral Equipment". For Overload protection time characterstics, refer to P.6-17.

• The SEMI F47 is the standard for the semiconductor when voltage sag.
• The control voltage of driver is following the SEMI F47 standard.
  The main voltage of driver is following the SEMI F47 standard for under no load or light load.
  Caution →
  1. Excluding the single-phase 100V type
  2. Please verify the actual compliance of your machine with the SEMI F47 standard for voltage sag immunity.

		Driver	Motor
EC Directives	EMC Directives	EN55011 EN61000-6-2 EN61000-6-4 EN61800-3	-
	Low-Voltage Directives	EN61800-5-1	EN60034-1 EN60034-5
	Machinery Directives Functional safety *1	ISO13849-1 (PL e, Cat. 3) EN61508 (SIL 3) EN62061 (SILCL3) EN61800-5-2 (SIL 3) IEC61326-3-1 IEC60204-1	-
UL Standards		UL508C (E164620)	UL1004-1, UL1004-6 (E327868)
CSA Standards		C22.2 No.14	C22.2 No. 100-04
Radio Waves Act (South Korea) (KC)*2		KN11 KN61000-4-2, 3, 4, 5, 6, 8, 11	-

IEC: International Electrotechnical Commission           Pursuant to the directive 2004/108/EC, article 9(2)
EN : Europaischen Normen           Panasonic Testing Center
EMC: Electromagnetic Compatibility           Panasonic Service Europe, a division of
UL : Underwriters Laboratories           Panasonic Marketing Europe GmbH
CSA: Canadian Standards Association           Winsbergring 15, 22525 Hamburg, F.R. Germany.
•When export this product, follow statutory provisions of the destination country.
*1 A6 series standard type and communication type don't correspond to the functional safety standards.
*2 Information related to the Radio Waves Act (South Korea)
This servo driver is a Class A commercial electromagnetic radio wave generator not designed for home use. The user and distributor should be aware of this fact.